WELCOME:
-
FORSTER POWDER FUNNEL WITH LONG TUBE
R462,00This funnel and 5¼″ long drop tube combination can add from three to eight more grains of powder to your load, depending on the specific case you’re using. The Powder Funnel cleanly fills cases without any need to compress the charge during bullet seating.
The momentum of the powder dropping down the tube results in a larger volume by weight, so it’s not necessary to compress the charge.
The funnel works best with slow-burning powders when full capacity loads are desired. Works for a large range of cartridge cases starting with 223 Rem up to 375 H & H.
Confirm Stock Availability
-
Forster Primer Feed Tubes LARGE
R231,00The tube bottoms against the flat surface of the primer housing in the Co-Ax Primer Seater. The bottom of the tube must be funneled in slightly for proper functioning.
For several reasons, the tube is made of a light, soft material which may be bent, filed or trimmed with a penknife. The slot in the tube also permits visual inspection to determine if any primers are reversed.
Confirm Stock Availability
-
Forster Primer Seater Assembly
R322,00Co-Ax Reloading Press spare or replacement Primer Seater Assembly.
Confirm Stock Availability
-
FORSTER PRIMER TUBE LOADER
R392,00Aligns primers anvil-side up and mates with the Primer Feed Tube for quick loading in the Co-Ax Primer Seater.
The Primer Tube Loader aligns all primers with just a few flicks of the wrist. With a little practice, you can go from the primer box, to Primer Tube Loader, to Primer Feed Tube in as little as eight seconds!
Confirm Stock Availability
-
FORSTER Seating Stem for Seater Die
R308,00Replacement seating stem for Bench Rest Seater Die.
This part is not interchangeable with the Ultra™ Micrometer Seater Die Seating Stems.
Confirm Stock Availability
-
FORSTER Seating Stem for Ultra Die
R308,00Replacement seating stem for Ultra Micrometer Seater Die.
This part is not interchangeable with the Standard Bench Rest Seater Die Seating Stems.
Confirm Stock Availability
-
FORSTER Stuck Case Remover
R462,00We have developed this simple, inexpensive stuck case remover to work on most sizing dies. The unique design even works on stuck cases that have the decapping rod and expander ball stuck in the die.
- Designed for use with Forster Sizing Dies that feature the elevated “E-Z” Out Expander Ball in the Decapping/Expander Assembly
- May also be used with sizing dies that use ¼”-28 or 10-32 thread spindles
- All components hardened for long life
- Washer protects the top of your die
Confirm Stock Availability
-
FORSTER Ultra Micro Die
R6013,00Forster Reloading Dies are of excellent quality and provide the reloader with the ability to produce concentric rounds time and time again. Each die is manufactured from the finest quality steel carefully machined to very tight tolerances. Dies are hand polished both before and after the heat-treating process to guarantee an extra fine finish. All Forster reloading dies feature their Forster Cross Bolt Die Locking Ring that tightens the two ends of the split ring instead of tightening a screw directly into the threads of the die. The Forster Ultra Seater includes all of the features of the Forster Bench Rest Seater Die above, plus an ultra accurate micrometer adjustment. This micrometer adjustment allows you to adjust bullet seating depth from .0005 inch to .001 inch increments, and makes switching bullets easy – just dial back to your previous recorded setting. Forster Ultra Seaters make fine tuning your bullets to the lands of your rifling simple. These are XL dies that are 1-1/4″ built for the XL Coax Press and large cartridges
Confirm Stock Availability
-
FORSTER Ultra Micro Seater Die
R2800,00 – R2933,00The Ultra Micrometer Seater Die is a non-crimping style seater die (except for the 30-30) that holds the bullet and case in perfect alignment while the bullet is press-fit seated.
A handy micrometer fixes the bullet seating depth to your specifications. After you have seated your bullet close to the desired depth and measured it, simply adjust the Micrometer stem up or down to the desired depth and the cartridge will be exactly the length you need.
- Includes all the popular straight line seating features of the original Bench Rest Seater Die plus an ultra-accurate Micrometer for adjusting bullet seating depth
- Micrometer allows fine-tuning in either direction; easily adjustable to .0005″
- Gradations at increments of .001″ are clearly marked
- Eliminates much of the trial and error that was once associated with seating accurate rounds
- Bright, white markings make micrometer easy to read
Confirm Stock Availability